HomeProductsIndustrial Products
Back to Products

Industrial Products Industrial Cleaning and Maintenance Chemicals

A comprehensive family of chemical products developed for the maintenance, cleaning and hygiene needs of industrial plants. Our disinfectant products provide microorganism control in production areas and shared spaces. Degreasers effectively dissolve industrial oil, grease and dirt deposits on machine and equipment surfaces, speeding up maintenance work. Rust and scale removers extend equipment life by removing oxidation and limescale deposits from metal surfaces. Our general hygiene products are used to clean floors, surfaces and equipment throughout factories and plants. Our paint stripper gel quickly and effectively lifts old layers of paint from metal surfaces — it is particularly preferred on stainless steel surfaces. Our maintenance chemicals category covers the supporting products needed for the regular maintenance of production lines, machinery and plant infrastructure. All products are formulated to withstand intensive use on an industrial scale.

Key Features

  • Concentrated products
  • Economical use
  • High performance
  • Wide product range

A comprehensive family of chemical products developed for the maintenance, cleaning and hygiene needs of industrial plants. From degreasers to rust removers and from paint strippers to dielectric solvents, it covers almost every item on a factory's daily maintenance list.

In industrial cleaning, the most expensive mistake is choosing the wrong product. The right chemical finishes the job in a single pass; the wrong one either does not work at all or damages the surface. This page first answers the question of which product for which soiling, then describes the product groups one by one.

All the products come in concentrated form. They are used diluted with water, which reduces both transport costs and storage space.

Which product for which soiling?

The soiling found on an industrial surface falls into four main groups, and each requires a different chemical mechanism:

SoilingChemical characterSolutionProduct group
Oil, grease, carbonised dirtOrganic, non-polarAlkali or solvent — saponifies or dissolves the oilDegreasers
Rust, mill scale, oxideInorganic, metal oxideAcid — dissolves the oxideRust removers
Limescale, mineral depositsInorganic, calcium carbonateAcid — breaks down the carbonateDescalers
Paint, varnish, coatingsPolymer filmSolvent or gel — swells and lifts the polymer bondPaint strippers
MicroorganismsBiologicalDisinfectant — breaks down the cell wallDisinfectants

Rule: never mix acidic and alkaline products, and never apply them one after the other without rinsing in between. The neutralisation reaction releases heat and cancels out the effect of both products.

Second rule: acid does not work on an oily surface. The oil on the surface must be removed before a rust remover is applied — otherwise the acid never reaches the metal.

Degreasers

The types of oil encountered during machine maintenance, production line cleaning and floor care in industrial plants differ greatly. Fresh machine oil and tarry deposits baked on in an oven do not come off with the same product.

ProductBaseWhat forHow to apply
Concentrated water-based degreaserAlkaline, water-basedGeneral-purpose factory cleaning, floors, equipmentDiluted with water; spray, mop or immersion
Heavy-duty degreaserStrongly alkalineStubborn, tarry oil on floors and machinesAt a lower dilution, with a dwell time
Industrial degreaserAlkalineGeneral factory maintenance cleaningSpray or wipe
Textile oil and stain removerSpecial formulaRemoves stains without damaging the fabricDirectly onto the stain, after a fabric test
Dry Clean SolveWater-free solventSensitive parts, electrical components, surfaces that must not come into contact with waterWipe or immerse; no rinsing needed

Water-based or solvent-based? The decision comes down to two questions:

  1. Can the surface withstand water? Use a water-free solvent on electrical components, sensitive mechanical parts or machined surfaces that will rust on contact with water.
  2. Can you rinse? If the rinse water cannot be collected or there is no way to discharge it, choose a water-free product.

In all other cases, a water-based concentrate is more economical, safer and more environmentally suitable. Water-based products are not flammable; with solvent-based products, pay attention to the flash point and ventilation conditions.

The logic of dilution: using a concentrated degreaser at full strength for every job is a waste of money. Typical starting points are 1/20 for light soiling, 1/10 for medium soiling and 1/3 for heavy soiling. Try the most dilute ratio first; if it does the job, do not increase it.

Rust and scale removers

Corrosion that forms on metal surfaces over time, seized fasteners and limescale in water systems are the most common maintenance problems in industrial plants. Each calls for a different product:

ProductWhat it doesWhere
Rust removerDissolves corrosion on the metal surface and prepares the metal for paintingSteel structures, tank exteriors, vehicle bodywork, restoration
Rust remover (solvent-based)Loosens seized nuts, bolts and fittingsMaintenance and repair, dismantling work
Concentrated descalerDissolves limescale built up in water systems, boilers and pipesSteam boilers, heat exchangers, pipelines, dishwashers
Coil cleanerCleans the coils of air-conditioning and refrigeration systems, restoring airflow and efficiencyHVAC maintenance, chillers, condensers
METOX DRPDissolves rust, mill scale and limescale on iron and steel in an immersion bath; does not damage the surface geometryPost-casting cleaning, pre-weld preparation, complex parts

Why should coil cleaning not be neglected? The layer of dust and oil that builds up on the coils of air-conditioning and refrigeration systems insulates the heat transfer surface. The system runs longer to provide the same cooling, and electricity consumption rises. Coil cleaning is a maintenance item that shows up directly in the energy bill.

Always neutralise and protect after rust removal. Bare metal coming out of an acid treatment rusts faster on contact with air than it did before treatment. The sequence rinsing → neutralisation → drying → protective coating or paint must not be skipped.

Paint strippers

Before repainting, restoration or surface preparation, old layers of paint have to be removed. The type of material determines the choice of product:

ProductWhat forWhy
Solvent-based paint stripperQuickly strips all types of paint from metal and wooden surfacesWidest range of action, fastest result
Gel paint stripperVertical surfaces, ceilings, upright columnsDoes not run; stays on the surface and lifts the paint
Aluminium paint stripperWheel rims, aluminium window and door frames, delicate aluminium partsWorks without pitting or darkening the aluminium

Why is a product specific to aluminium needed? Most standard paint strippers contain strong alkalis. Aluminium is an amphoteric metal — it reacts with both acids and strong alkalis, its surface becomes pitted and it darkens permanently. On an aluminium wheel rim, this means the part has to be scrapped.

The practical benefit of the gel form: on a vertical surface, a liquid paint stripper runs down within seconds and is not in contact with the paint for long enough. A gel stays in place, extends the contact time and gives results in a single application.

Disinfectants

Developed to maintain hygiene standards in industrial and institutional settings, the disinfectant group covers both staff hygiene and surface disinfection. It is suitable for regular use in food production plants, healthcare facilities, offices and industrial plants.

  • Antibacterial hand and skin cleansing solutions — clean and disinfect without drying the skin. In food and healthcare environments where frequent hand washing is mandatory, protecting the skin barrier directly affects compliance.
  • Surface disinfectants — fast-acting products used on tables, door handles, equipment and hard surfaces.

Cleaning and disinfection are not the same thing. A disinfectant does not work on a dirty surface: organic residue binds the active substance and renders it ineffective. The correct sequence is always first cleaning, then rinsing, then disinfection.

Observe the contact time. Every disinfectant has a contact time stated on its label. The surface must stay wet for that time; a disinfectant that is wiped off immediately has not done its job.

General hygiene products

Basic products that meet day-to-day hygiene needs throughout the plant:

  • Liquid hand soap — a pleasantly scented cleanser suited to the skin's pH
  • Concentrated liquid hand soap — an economical option used diluted
  • Drain and sewer openers — chemically clear blocked sinks, toilets and sewer drains and remove unpleasant odours

Safety warning for drain openers: never pour drain openers of different brands or of a different nature (acidic/alkaline) one after the other. The reaction releases heat and gas. If one product has not worked, rinse with plenty of water and try a mechanical method (a drain auger).

If sewer lines suffer from recurring blockages and odour problems, a biological solution is more lasting than a chemical opener

Industrial maintenance chemicals

Special-purpose products for the regular maintenance of production lines, electrical infrastructure and machinery:

ProductWhat it doesKey property
Dielectric solventCleans electric motors and electrical panelsCan be used while energised, non-flammable, non-conductive
Mould release agentsMake it easier to remove parts from the mouldSilicone and silicone-free options
Hand cleaning creamsRemove heavy industrial dirt from the handsGranular texture; does not irritate the skin
METOX AS‑05Prevents weld spatter from sticking to the surfaceWater-based, non-flammable, paintable, silicone-free

Why is dielectric solvent a separate product? A fluid used to clean an electrical panel or motor must meet two conditions: it must not conduct electricity and it must not burn. A standard cleaner meets neither — water conducts and solvents are flammable. Dielectric solvent makes it possible to carry out maintenance without shutting the system down, which directly eliminates the cost of a production stoppage.

Choosing silicone or silicone-free mould release: if the moulded part is to be painted or bonded later, use a silicone-free product. Silicone residue prevents paint adhesion and causes craters ("fish eyes") on the surface.

METOX AS‑05 is applied to the surface and the torch nozzle before welding; spatter does not stick to the surface and is cleaned off with a simple brush. It is aerosol-free, 100% liquid and odourless, and does not interfere with subsequent painting or coating. It is available in 30 kg jerrycans and 1,000 kg IBCs.

The economics of using concentrates

The fact that the products are concentrates is not just a formulation choice; it is a direct cost item.

Transport and storage. 30 kg of concentrate diluted 1/10 is equivalent to 300 kg of ready-to-use product. The 270 kg of water in between is neither transported nor stored.

Flexibility of use. From the same product, a 1/20 mix is prepared for light soiling and a 1/3 mix for heavy soiling. Ready-to-use products do not offer this flexibility.

Three rules for correct dilution:

  1. Always add the chemical to the water, never the other way round. Doing it the other way round is dangerous, especially with acids.
  2. Measure when mixing; do not judge by eye. Excess concentration brings no extra benefit and increases the risk of damaging the surface.
  3. Use the mix within the day. Diluted products have a shorter life than the concentrate.

Safety and storage

  • Personal protective equipment. Gloves and goggles are mandatory with acidic and alkaline products; solvent-based products also require ventilation.
  • Separate storage. Acids and alkalis must be kept on separate shelves. If something tips over, it is dangerous for them to mix.
  • Original packaging. Do not decant products into food containers or unlabelled containers.
  • MSDS. The safety data sheet for every product must be accessible on site.
  • Discharge. Acidic and alkaline rinse water must not be discharged to the sewer without pH adjustment.

Quick Action

Request a quote now to get detailed information, request technical specifications or place an order for this product.

Technical Documents

You can request MSDS and TDS documents from our technical documents page.

Industrial Products — Frequently Asked Questions

If the surface can withstand water and you are able to rinse, a water-based concentrate is the most economical choice. On electrical components, sensitive mechanical parts or where rinsing is not possible, use a water-free solvent (Dry Clean Solve). Tarry, baked-on oil requires a heavy-duty degreaser.

Typical starting points are 1/20 for light soiling, 1/10 for medium soiling and 1/3 for heavy soiling. Start with the most dilute ratio; if it does the job, do not increase it.

Do not. Most standard paint strippers are strongly alkaline and will pit the aluminium surface and darken it permanently. Use a product specially formulated for aluminium.

Bare metal coming out of an acid treatment rusts faster than before treatment. The sequence of rinsing, neutralisation, drying and protective coating must not be skipped.

No. A disinfectant does not work on a dirty surface; organic residue binds the active substance. Clean first, then rinse, then disinfect.

Dielectric solvent is made for this job — it does not conduct electricity and does not burn. This must not be done with standard cleaners.

Do not. The reaction between acidic and alkaline products releases heat and gas. If one product has not worked, rinse with plenty of water and try a mechanical method.

If the moulded part is to be painted or bonded, use silicone-free; silicone residue prevents paint adhesion and causes craters on the surface.

Water-based products are not flammable. With solvent-based products, pay attention to the flash point and ventilation conditions, and consult the product's safety data sheet (MSDS).

Tell us your type of soiling and your surface material; we will identify the right product and dilution ratio, and you can run a trial with a sample. Contact: +90 212 222 37 52 · satis@akemkimya.com.tr