Home/Blog/Aircraft De-icing Fluids: Type I/II/III/IV De-icing and Anti-icing Differences
Back to Blog

Aircraft De-icing Fluids: Type I/II/III/IV De-icing and Anti-icing Differences

What Is De-icing (Type I)?

It is applied to melt ice, snow and frost that have already formed on the aircraft surface. It is usually glycol-based and is sprayed diluted and heated. It is defined by the SAE AMS 1424 standard.

What Is Anti-icing (Type II/III/IV)?

It is a thicker/more viscous fluid applied after de-icing to prevent re-icing in the period up to take-off. It must comply with the SAE AMS 1428 standard. The length of this period is called the "holdover time" — the longer it is, the safer it is for the pilot.

The PLAS P AIRCRAFT series is an aircraft de-icing fluid that meets both Type I and Type II requirements and protects the surface without impairing its aerodynamics.

Technical Properties of PLAS P AIRCRAFT

Manufactured on a propylene glycol (MPG) basis, PLAS P AIRCRAFT complies with ISO 11078, ISO 11075, AMS 1424 and AMS 1428; it can be produced with a 55% MPG base for standard commercial use and also with an 88% MPG base for military specifications. The clear fluid has a density of approximately 1.04 g/cm³ at 20 °C; its pH value is 8.0–9.5 for Type I and 7.0–7.5 for Type II. When diluted 1:1 with water, the freezing point is below −25 °C for Type I and below −10 °C for Type II; this value changes with the dilution ratio. The product has a shelf life of at least 2 years in its original, unopened drum.

Performance Data: Holdover Time and LOUT

In AMS 1428 qualification tests, PLAS P AIRCRAFT at 100% concentration and −5 °C achieved a WSET (Water Spray Endurance Test) time of 30 minutes and an HHET (High Humidity Endurance Test) time of more than 5 hours (against 4 hours). The LOUT (Lowest Operational Use Temperature) at 100% concentration was determined as −27 °C. In aerodynamic acceptance tests, it shows a typical elimination performance of 90% regardless of temperature and concentration (minimum required: 74%).

Material Compatibility and Aircraft Safety

The compatibility of PLAS P AIRCRAFT with aircraft structural materials was tested according to ASTM standards on clad 2024-T3 and bare/clad 7075-T6 aluminium alloys, magnesium (AZ31B-H26), titanium (6Al-4V), carbon steel and low-embrittlement cadmium plating, and all of them gave a "conforms" result. In addition, no adverse effect was found in the hydrogen embrittlement (ASTM F519), acrylic/polycarbonate stress crazing (ASTM F484) and painted/unpainted surface tests — showing that the product can be used without damaging any critical component of the aircraft.

Environmental Profile

According to the Zahn-Wellens test, the product is more than 99% biodegradable within 5 days. The COD / BOD₅ values are 1.3 / 0.66 kg O₂/kg for Type I and 0.83 / 0.28 kg O₂/kg for Type II. In aquatic toxicity tests, a zebra fish LC50 of 7,071 mg/L (96 hours) and a Daphnia EC50 above 10 g/L (48 hours) were measured for Type I, and a rainbow trout LC50 of 2.4 g/L (96 hours) and a Daphnia EC50 of 1.0 g/L (48 hours) for Type II — showing that the product poses a low risk in terms of acute aquatic toxicity. The heavy metal contents (lead, chromium, cadmium, mercury) are all below 0.2 ppm.

Application and Spray Behaviour

Field trials show that PLAS P AIRCRAFT has a low tendency to foam and works compatibly with most spray equipment. When it dries, the product leaves a thin, oily film or a fine white powder; it does not form gum-like residues, thick gel or hard/coarse solids — the remaining residues dissolve easily in water. It can be applied hot or cold, neat or diluted. On the operating site, in accordance with the regulations, it is used at different dilution ratios such as 100/0, 75/25, 50/50 and 25/75, depending on the air temperature. In shear stability tests (Brookfield mixer, 3,500 rpm, 5 minutes, 20 °C), only a 10% loss of viscosity was observed; this shows that the product largely retains its physical properties even when passing through high-pressure spray systems.

Related Product

PLAS P AIRCRAFT

Technical Documents

You can request MSDS and TDS documents from our technical documents page.