Preparing for Winter: How to Choose the Right De-icing Solution
Salt or Solution?
Although traditional salting methods (road salt, NaCl) are cheap, they cause corrosion on concrete and metal surfaces, lose much of their effect below −10 °C and leave lasting damage to soil and water sources. A modern de-icing solution is formulated precisely to solve these three problems.
Criteria to Look For
- Low-temperature performance — A serious snow-melting solution should remain effective below −30 °C as well.
- Fast reaction — It should take effect within seconds and should not require a long wait.
- Preventing re-icing — A one-off effect is not enough; it should delay re-freezing by leaving a protective film on the surface.
- Surface-friendly formula — A salt-free, non-corrosive anti-icing solution protects the service life of concrete, asphalt and metal equipment in the long term.
- Environmental impact — It should be biodegradable.
PLAS ICE meets all of these criteria with performance down to −40 °C: it is salt-free, leaves no residue or deposits, and can be applied by both spraying and pouring.
The Real Cost: The Hidden Price of Salt
Although salt looks cheap in the short term, the corrosion it causes leads to long-term repair costs for vehicles, equipment, concrete floors and metal structures. A salt-free snow and ice de-icing solution eliminates this hidden cost.
Where Is It Used?
It is applied safely on highways, airport perimeter roads, factory yards, ramps, car parks and areas with heavy pedestrian traffic.
Technical Properties and Independent Laboratory Verification
According to the ASTM D 7153 standard, PLAS ICE has a freezing point of −40 °C or lower, a pH range of 5–11 and a non-flammable structure. In corrosion tests (ASTM F483), the values must remain below 0.05 mg/cm²/day on carbon steel and 0.02 mg/cm²/day on aluminium; asphalt compatibility is verified with the Marshall stability test (provided the loss does not exceed 5%). In the 2024 independent analysis report of the Department of Chemistry of Yıldız Technical University, the product met all of these specifications: the freezing point was measured at −42.8 °C, exceeding even the specification, the corrosion values were well below the limits (0.027 carbon steel, 0.016 aluminium) and the Marshall stability loss was found to be only 2.1%. The same report confirmed that, in a field test on an asphalt road with an 8% gradient, the product remained effective for 48 hours and caused no adverse deformation of the road superstructure (bitumen/aggregate adhesion).
Performance Comparison Against Salt
According to direct comparative data, the freezing point of salt (NaCl) is at most −7 °C, whereas PLAS ICE is effective down to −40 °C. While salt usually has to be reapplied after 6 hours (8 times in 48 hours), PLAS ICE maintains its effect for at least 48 hours with a single application — which directly reduces labour and material costs. The corrosive effect of salt is approximately 7.5 times that of water and causes scaling and cracking on concrete surfaces, whereas no such effect has been observed with PLAS ICE. Although the unit cost of salt appears lower, the total cost of PLAS ICE turns out to be lower once frequent application, labour and infrastructure repair costs are added up.
How Is the Right Dosage Determined?
For applications aimed at preventing icing before snowfall (anti-icing), a dosage in the range of 100–150 g/m² is sufficient. For applications aimed at melting an ice layer that has already formed on the ground (de-icing), the dosage varies between 150 and 350 g/m² depending on the thickness of the ice — thick ice layers require a higher dosage. At an air temperature of −15 °C, a 1 cm thick layer of ice melts in approximately 30 minutes. In extreme conditions where the road temperature falls below −40 °C or where a very thick layer of snow has accumulated on the ground, it is recommended to clear the snow mechanically first and then apply the solution; otherwise more product than necessary will be consumed.
Related Product
PLAS ICE
You can request MSDS and TDS documents from our technical documents page.