Stainless Steel Weld Cleaning Guide: Electrochemical Machine, Paste or Spray?
Why Is Post-Weld Cleaning Necessary?
The heat tint and oxide layer formed on the metal surface after TIG, MIG and spot welding damage the steel's natural protective passive layer (chromium oxide). When this layer is damaged, stainless steel — contrary to its name — becomes vulnerable to rusting.
After TIG (argon), MIG, laser and spot welding, blue, purple and yellow discolouration forms in the weld zone of stainless steel (inox). The corrosion resistance of this zone is low; rust usually starts here first. That is why weld marks must be cleaned and the surface re-passivated not only for appearance, but also to restore corrosion resistance.
Comparison of Three Cleaning Methods
Mechanical grinding: Physically scrapes off the top layer with grinders and abrasives. It is time-consuming and rarely gives the desired aesthetic result.
Chemical gel (acid-based): It is effective but has serious drawbacks — most weld cleaning pastes contain hydrofluoric, nitric and sulfuric acids; they can cause serious harm to the skin and internal organs, can only be used by certified operators wearing full protective equipment, and waste management creates an environmental burden.
Electrochemical weld cleaning machine: Using a mild electrolytic fluid and a weak electric current (AC/DC), it carries out cleaning and passivation simultaneously within seconds. Special protective equipment is generally not required, and there is no requirement for certified operators.
In METOX 500 / 600 machines, the carbon brush is dipped into METOX KTS 501 solution and moved over the weld zone. A low-voltage (14 V) current flows between the brush and the part; the thermal oxide layer is detached from the surface by an instant electrochemical reaction, and the same reaction allows the chromium oxide layer to re-form. No tone differences, swirl marks or dulling occur.
Chemical Pickling: Paste or Spray?
METOX W-2000 pickling paste is for spot application on weld seams: it is brushed onto the weld zone and left for 15–60 minutes (depending on temperature, steel grade and contamination). It does not run on vertical surfaces or in overhead positions; 1 kg cleans 150–250 m of weld seam. It is suitable for AISI 304, 316, 321 and their derivatives; the working area must be above +10 °C.
METOX S-3000 pickling spray is for large surfaces: it is sprayed thinly and evenly over the entire surface with an acid-resistant pump. For grades 304 and 316, the typical reaction time is 60 minutes at 20 °C and 45 minutes at 30 °C. It complies with the requirements of ASTM A-380 A.1 and BS CP 312.
Comparison Table
| Grinding / brushing | Chemical pickling (paste / spray) | Electrochemical (METOX 500/600) | |
|---|---|---|---|
| Method | Mechanical abrasion | Dissolution with acid | Controlled current + solution |
| Removes discolouration | Yes (visually) | Yes | Yes |
| Removes the chromium-depleted layer | Partially | Yes | Yes |
| Passivation | Separate step | Separate step | In the same step |
| Surface appearance | Swirl marks, tone difference | Uniform matt | Original appearance |
| Material loss | Yes | At micron level | None |
| Time | — | Paste 15–60 min; spray 45–60 min | Seconds |
Comparison of Corrosion Resistance
Independent tests show that the electrochemical method provides the highest corrosion resistance of all cleaning techniques — clearly ahead of mechanical grinding and pickling methods. The main reason: the electrochemical process guarantees re-passivation together with cleaning; grinding and gel methods do not.
Step by Step with a Weld Cleaning Machine
- Remove oil, dust and coarse dirt from the area to be cleaned; the reaction does not work properly on an oily surface.
- Connect the METOX 508 earth clamp to the workpiece at a clean metal surface; attach the METOX 503 brush holder to the machine.
- Fit the METOX 502 carbon brush into the brush holder and switch on the machine.
- Dip the brush into METOX KTS 501 weld cleaning solution.
- Move the brush over the weld zone with steady movements; do not press, contact is enough. Dip the brush into the solution frequently.
- Rinse the surface with plenty of water.
Wear chemical-resistant gloves and safety goggles while working; follow the relevant Safety Data Sheets for the solutions.
Step by Step with Pickling Paste (METOX W-2000)
- Mix and shake before use.
- Apply to the weld zone with a brush.
- Leave for 15–60 minutes; the working area must be above +10 °C.
- Remove the residues with a high-pressure water jet or a stainless steel brush, then finally clean with water.
- Neutralise the acidic rinse water with METOX N-3000; do not discharge it directly.
Protective acid-resistant clothing, a mask, goggles and gloves must be worn during application.
Which Method Should You Choose?
Weld seam cleaning, on site or in the workshop, where surface appearance matters: Electrochemical machine. It is portable (METOX 500: 7.4 kg; METOX 600: 11.2 kg) and carries out passivation in the same step.
Food, dairy, beverage, pharmaceutical and chemical equipment: In the machine's AC mode, no material is removed from the surface and the surface roughness does not change; this is why it is preferred for such equipment.
Spot chemical application on seams in vertical and overhead positions: METOX W-2000 paste.
Large surfaces such as tanks and large structures: METOX S-3000 spray.
Passivation and Waste After Pickling
To improve the result after chemical pickling, passivation with METOX P-3000 or the acid-free METOX H-3000 is recommended. Pickling waste water contains acid; before discharge it must be brought to the pH 7–10 range with METOX N-3000 or slaked lime.
Fixed Bath or Portable Machine?
Electrolytic immersion baths are installed in fixed production facilities and have high construction/maintenance/operating costs; they affect the entire part. Portable devices such as the Weld Cleaning Machine, on the other hand, can be used on site and target only the weld zone and the heat-affected zone — they provide more precise control, and their initial investment and consumable costs are much lower.
The Difference Between METOX 500 and METOX 600
METOX 500 quickly restores a clean surface on welded stainless steels without causing tone differences or dulling; it also offers high-quality marking (logo/text marking).
METOX 600 is one of the most powerful electrolytic weld cleaners on the market — it is built to withstand heavy use on larger surfaces; in addition to cleaning and marking, it also offers polishing (electropolishing).
METOX 500: weld cleaning, passivation and marking (14 V AC), 7.4 kg. METOX 600: more powerful cleaning than METOX 500; additionally electropolishing and etching (deep marking) with DC (14 V AC/DC), 11.2 kg. Both models are used on 304/304L, 316/316L, duplex and super duplex, 904L and ferritic (430) stainless steels; the warranty is 2 years.
Not to Be Confused with Electropolishing
While weld cleaning removes contamination without changing the surface, electropolishing removes a microscopic layer of the surface, reducing roughness and improving the aesthetic appearance — the two processes complement each other; one does not replace the other.
Frequently Asked Questions
It is removed within seconds with an electrochemical weld cleaning machine, with pickling paste by rinsing after a dwell time of 15–60 minutes, or with pickling spray on large surfaces.
It is used on 304/304L, 316/316L, duplex and super duplex, 904L and ferritic (430) stainless steels.
15–60 minutes for METOX W-2000; the time varies with temperature, steel grade and contamination.
Related Product
Weld Cleaning Machine
You can request MSDS and TDS documents from our technical documents page.